PRODUCTS
You are here: Home » Products » solar water heater » compact solar water heater » non-pressure solar water heater
Share to:

non-pressure solar water heater

Quantity:



TypeEvacuated Tube
PressureUnpressurized
Circulation TypeOther
Heating SystemThermosyphon (Passive)
Connection TypeDirect-Plug
CertificationCE, Solar Keymark, SABS
Model NumberTZ58/1800-10,12,14,15,16,20,24,30
Recommend regionAsia, Africa, Latin America


Inner tank: stainless steel SUS304-0.5mm

Vacuum tube: QB-AL-N/AL-47-1500/58-1800

Outer tank: painted steel-0.4mm/aluminum-zinc coated steel-0.45mm/stainless steel SUS304

Insulation: polyurethane

Frame: coated galvanized steel-1.5mm/stainless steel SUS430-1.5mm


Principle:

1.6

The vacuum tubes trap incident sun rays, and convert it to heat inside the inner tube. Water, now being heated its temperature rises, density changes, and hot water sections rise through the tube to the top of the tank, while cold water from the bottom of tank replaces it in the tube, to start the cycle again. This natural cycling of water driven by temperature difference keeps water hot when stored in an insulated tank.




1.7The Solar Water heater tank is a non-pressurized tank, and has an opening to the ambient atmosphere. Solar water heater tank should always be filled with water to avoid damage caused by dry high temperature working conditions. The stainless steel our use belong to food grade, and SUS 304 & SUS 316 have better corrosion resistance.



Thermal Performance

The system passes over thermal performance test according to EN12976-2:2006-chapter 5.8, parts of the test conditions are listed below:

1.4

Model

Ac*[m²]

uc*[W/(m²K)]

Us[W/K]

Cs[MJ/K]

DL[-]

TZ58/1800-12

1.145

2.758

1.766

0.605

0.301

TZ58/1800-14

1.347

2.758

2.060

0.706

0.301

TZ58/1800-16

1.527

2.758

2.355

0.807

0.301

TZ58/1800-18

1.589

2.758

3.298

0.898

0.352

TZ58/1800-20

1.916

2.758

2.943

1.009

0.301

TZ58/1800-24

2.298

2.758

3.532

1.210

0.301

TZ58/1800-30

2.874

2.758

4.415

1.513

0.301



1.5

Ac*

[m²]

effective collector loop area

uc*

[W/(m²K)]

effective collector loop heat loss coefficient

Us

[W/K]

heat loss rate of the store

Cs

[MJ/K]

thermal heat capacity of the store

DL   

[-]

mixing constant, describing mixing effects during draw-off


Pre-installation Considerations

Before installation, please note:

1. Check the density, hardness and strength of roof structure to ensure safety of solar water heater.

2. The maximum snow load is: 1.2 times the weight of tank

3. Maximal wind resistance for the frame is 1000Pa, according to ENV1993-1-1.


1.8


Solar System Location

The solar system must be installed in a non-shaded place. High buildings or trees may cause shade to solar water heater and reduce its performance.

For optimum performance, solar water heater should be installed facing towards the equator. For South Hemisphere solar water heater should be installed facing north, while for North Hemisphere should be facing south. Diverting for this north/south orientation is possible, given installation site conditions, and is best considered by your dealer’s appointed professional installers.


1.9


7.3 Key Points to Pipeline Installation

The connection of water pipes and tank uses a non-welding technique.

Always use a spanner, when tightening pipes on the tank

1. Always use a spanner to fix the pipes of the tank for any connections.

2. Prevent twisting force to the pipe to avoid damage to the seal.

3. Prevent any axial force to the pipe to avoid damage to the seal.


2.0


Important Notice

1. Solar water heater should face the sun, with 10° to 20° variation southwest. Be sure there is no shade on both sides of solar water heater.

2. Solar water heater should be fixed with roof firmly with expanding screw and/or steel wire to avoid potential danger against heavy wind.

3. Be sure that no leakage in pipeline, joints, valves and so on.

4. Pipeline should be insulated to avoid heat loss. For cold area usage, use electrical heating cable to protect against freezing.

5. If the area is prone to lightning strikes, with no existing protection then, user should add the lightning conductor fixture for protection against lightning.


2.12.2



TZ58/1800-10TZ58/1800-12TZ58/1800-15TZ58/1800-18TZ58/1800-20TZ58/1800-24TZ58/1800-30
GENERAL PARA.
absorbing area (m2)1.3891.6472.0852.4782.7553.310 4.142
operating pressure (bar)0
ambient temperature0-60 ℃
daily efficiency>=55%
empty weight (kg)40465265717998
loading qty (20/40/40HQ)48/100/11648/100/11640/80/8836/72/8032/68/7228/56/6422/44/52
STORAGE TANK
capactiy (L)100120150180200240300
outer material (mm)painted steel 0.4mm●  stainless steel 0.4mm○  galvanized 0.4mm○
inner material (mm)stainless steel 304 0.5mm●  stainless steel 316L 0.5mm○
insulation (mm)PUF 50mm
electric heater
nipple size1/2"●  3/4"○
feeder tank
welding
reflector
controller
tank packing size (mm)1120*560*5601320*560*5601570*560*5601810*560*5601980*560*5602310*560*5602830*560*560
VACUUM TUBE
size58/1800mm
tube qty10121518202430
tube packing size (mm)1880*330*250
FRAME
materialgalvanized● stainless steel○ aluminum○
inclined roofgalvanized ○
angle45°● 30°○








NOTE:






● - standard






○ - optional







Our Company

Product Category

Contact Us

     +86-13775482716
     info@sunrain.com
    199#Yingzhou Road, Lian Yungang, Jiangsu province, China
Based on science and technology ......
​© Copyright 2020  SUNRAIN   Support by Leadong